1
For Sale/Wanted / Conical mount for a Long
« on: June 30, 2011, 08:30:48 PM »
Planning to use my 290G conversion and need a conical mount.
Thanks Bill
Thanks Bill
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Hangar Flying / Re: comm antenna
« on: April 24, 2009, 04:18:44 PM »
You may want to check out Advanced Aircraft Electronics on the web.
Bill
Bill
3
Hangar Flying / Re: What system to use?
« on: March 05, 2009, 09:29:58 AM »
Great feedback! there are 3 hardners ----Recomendations? also has anyone checked out the price for a 5 gallon Kit at Aircraft Spruce? OUCH!!! We need some bailout money.
Thanks Bill
Thanks Bill
4
For Sale/Wanted / Re: Shimmy Damper for --Vari-Long-Cozy-E-Racer
« on: March 03, 2009, 09:54:45 AM »
I have a couple Kits left, when they are gone there gone. Yell if you want one.
Bill
Bill
5
Hangar Flying / Re: What system to use?
« on: January 11, 2009, 08:49:33 PM »
Great info so far, I live in Lake Elsinore Ca, 90s is not a probem. I'll be doing this in my garage. I want all the input I can get before starting and no better place to go than the guys that have been there.
Bill
Bill
6
Hangar Flying / What system to use?
« on: January 10, 2009, 08:08:33 PM »
I'm going to build the wings on my long project soon, and read somewhere that the West System with slow hardner will work fine.
I'm looking for any and all comments before starting.
Thanks
Bill
I'm looking for any and all comments before starting.
Thanks
Bill
7
For Sale/Wanted / Re: Shimmy Damper for --Vari-Long-Cozy-E-Racer
« on: November 12, 2008, 04:57:28 PM »
Tom.
There is a roll pin that has to be pressed out or as I did knocked out, Then you need to have the old shaft Pressed out and the new one pressed in.(The guy that did the machine work did mine for me, but some auto part stores may have a press) then you need to drill a new hole for the roll pin. All in the instructions.The shaft is hollow,Isuggest you drill from one side then flip it over and drill from the other side. It keeps the drill from"walking".
Bill
There is a roll pin that has to be pressed out or as I did knocked out, Then you need to have the old shaft Pressed out and the new one pressed in.(The guy that did the machine work did mine for me, but some auto part stores may have a press) then you need to drill a new hole for the roll pin. All in the instructions.The shaft is hollow,Isuggest you drill from one side then flip it over and drill from the other side. It keeps the drill from"walking".
Bill
8
For Sale/Wanted / Re: Shimmy Damper for --Vari-Long-Cozy-E-Racer
« on: November 12, 2008, 10:18:15 AM »
They are on the way.
Questions ?? You can also email me at b.cloninger at verizon.net
Bil
Questions ?? You can also email me at b.cloninger at verizon.net
Bil
9
For Sale/Wanted / Re: Shimmy Damper for --Vari-Long-Cozy-E-Racer
« on: November 11, 2008, 01:26:10 PM »
Hi Tom,
I have pic's I'm not sure how to post them. Give me your email and I will shot them directly to you.or give it to me over the phone. 951 245 8479
Bill
I have pic's I'm not sure how to post them. Give me your email and I will shot them directly to you.or give it to me over the phone. 951 245 8479
Bill
10
For Sale/Wanted / Shimmy Damper for --Vari-Long-Cozy-E-Racer
« on: November 07, 2008, 02:17:12 PM »
Kept reading about nose gear failure due to Gear shimmy, so I had one made up for mine and several extra.
Made to Davenport's specs the Kit includes all you need for the conversion.with Drawings and instructions.
$110.00 shipped (U.S.) Please call if you have any questions 951 245 8479
Bill
Made to Davenport's specs the Kit includes all you need for the conversion.with Drawings and instructions.
$110.00 shipped (U.S.) Please call if you have any questions 951 245 8479
Bill
Pages: [1]